Star pager r9500 manual

Ready for the plunge? Search in Blog go. Derniers avis Par Arif F. Les batteries m'ont permis de faire une Livraison rapide. Tous les avis. Nos marques. Contact us. My Account. Express delivery. Professional quality. Manufacturer Warranty Professional advice on more than 2, references. If anything is missing, contact the dealer where you bought the printer and ask them to supply the missing part.

Note that it is a good idea to keep the original box and all the packing materials just in case you need to pack the printer up again and send it somewhere at a later date. Protect your printer from excessive heat such as direct sunlight or heaters, and.

To disconnect the printer, the plug has to be disconnected from the wall socket,. Be careful not to drop paper clips, pins or other foreign matter into the unit as these cause the printer to malfunction.

Do not attempt to print when either paper or ribbon cartridge is not located in the printer, otherwise the print head can be damaged. Do not open the cover while printing. Do not touch the print head immediately after printing as it gets very hot. Use only roll paper that is not glued to the core. When the paper end mark appears on the paper, replace the roll paper before it runs out. Essentially, your printer is a robust piece of equipment, but should be treated with a modicum of care in order to avoid malfunctions.

For example:. Roughly speaking, if you feel comfortable, then the environment is suitable for your printer. Do not subject the printer to physical shocks or excessive vibration. Avoid over-dusty environments. Dust is the enemy of all precision mechanical devices. To clean the exterior of the printer, use a cloth barely dampened with either water with a little detergent or a little alcohol, but do not allow any liquid to fall inside the printer.

The interior of the printer may be cleaned with a small cleaner or a com- pressed-air aerosol sold for this purpose. When performing this operation, be sure not to bend or damage any cable connections or electronic components. Connects to peripheral units such as cash drawers, etc. Do not connect this to a telephone. In the case of a parallel interface, fasten the connector clasps. You can connect a peripheral unit to the printer using a modular plug. The following describes how to install the ferrite core and make the actual connection.

Note that this printer does not come with a modular plug or wire, so it is up to you to obtain one that suits your needs. Make sure that the printer is turned off and unplugged from the AC outlet and that the computer is turned off before making connections. Do not connect a telephone line into the peripheral drive connector. Failure to observe this may result in damage to the printer. Also, for safety purposes, do not connect wiring to the external drive connector if there is a chance it may carry peripheral voltage.

Also make sure the power cable plug is disconnected from the AC outlet. Also make sure the plug on the power cord matches the AC outlet. If the voltage shown on the label on the of your printer does not match the voltage for your area, contact your dealer immediately. We recommend that you unplug the printer from the power outlet whenever you do not plan to use it for long periods.

Because of this, you should locate the printer so that the power outlet it is plugged into is nearby and easy to access. It is not necessary to install the switch blind. Only install it if it is necessary for you. By installing the switch blind, the following become possible. The power switch can be turned ON! Notched part. If loading of the ribbon cartridge is not satisfactory, press down the cartridge while rotating the ribbon feed knob in the direction of the arrow. Note: When removing the ribbon cartridge, raise the A section and then remove it by holding the B section as shown in Fig.

Do not touch the print head immediately after printing as it can be extremely hot. Do not touch the cutter blade. Not only should you not put your hand in the paper outlet slot while printing is in progress, never put your hand into the outlet even when printing is not in progress. Note: When the paper end mark appears on the paper, replace the roll paper before it runs out. If loading of the ribbon cartridge is not satisfactory, press down the cartridge while.

If inserted correctly, the edge of the paper will pass through the auto cutter paper slit. Press the FEED. Note: When the paper end mark appears on the paper, replace the paper roll before it runs out. When using a paper roll with an 58 mm width, install the attached roll paper guide in the groove in the printer.

The setting for memory switch 2-A and 2-B must be changed to change the print width from 63 mm to 45 mm. For instructions on setting the memory switch, please refer to the separate Specification Manual. Note: Do not touch the print head immediately after printing, as it can be extremely hot. In addition, do not touch the cutter blade on models equipped with the auto cutter. Personal injury could result.

Because the near end sensor is not installed at the time of shipment factory setting , the error is not displayed if the sensor is not installed. A print head temperature error is not abnormal. Automatically the printer is recovered if the carriage returns to the home position after turning the power OFF and ON. Clear the jammed paper and change the paper roll if necessary. For incorrect paper format errors:. If a non-recoverable error occurs, turn the power OFF, wait at least 10 seconds, and turn the power back ON.

If the non-recoverable error continues to be indicated, consult a dealer for repairs. The device will enter the adjustment mode if your turn it on while pressing the FEED switch.

If the buzzer sounds five times or more, immediately turn the power off as the adjustment mode is cancelled. Self-printing will be performed according to the VER. When the FEED switch is held continuously or when the FEED switch is depressed at the time of the end of selfprinting, only the characters will be printed out repeatedly.

Each of the signals sent from the computer to the printer will be printed out in hexadecimal code. By connecting to a USB keyboard, you can edit memory contents directly.

The IC-R has two types of digital voice recorders. In SQ1 mode, up to minutes approx. The other recorder is the shor t voice recorder, which saves the previous 15 seconds of radio audio into RAM, allowing you to play back the audio instantly. Numerous scanning functions to search for desired stations are available to make operation easier.

The IC-R scans 40 channels per second in memory scan mode. The built-in synthesizer announces the receiving frequency, mode and signal strength in English. Received audio and the receiver configuration files can be imported and exported to a PC. Firmware upgrades are also possible via USB memory. IC-R Communications Receiver. Professional Communications Receiver with 0. Fixed mode Center mode